# Switching between Continuous Recording with a lower resolution to Event Recording with a higher resolution

**URL:** <https://community.mobotix.com/t/switching-between-continuous-recording-with-a-lower-resolution-to-event-recording-with-a-higher-resolution/3105>\
**Category:** Actions\
**Tags:** howto, resolution, recording\
**Created:** [September 11, 2020, 12:15pm UTC](https://community.mobotix.com/t/switching-between-continuous-recording-with-a-lower-resolution-to-event-recording-with-a-higher-resolution/3105 "2020-09-11T12:15:30Z")\
**Posts on this page:** 1\
**Page:** 1

<div class="post-metadata">

**Author:** ![Mx-MichaelD](https://avatars.discourse-cdn.com/v4/letter/m/f14d63/32.png) [@Mx-MichaelD](https://community.mobotix.com/u/Mx-MichaelD)\
**Post date:** [September 11, 2020, 12:15pm UTC](https://community.mobotix.com/t/switching-between-continuous-recording-with-a-lower-resolution-to-event-recording-with-a-higher-resolution/3105/1 "2020-09-11T12:15:30Z")

</div>

**Introduction**

When using continuous recording there needs to be a conscious effort to save resources on the both the camera and the network. However when an event or incident occurs, getting the best recorded footage is paramount. We can balance these two opposing needs by having two different recording settings; one for normal continuous recording with a lower resolution and another for event recording with a higher resolution, frame rate and image quality.

**Setting up Recording**

Here we will be configuring the camera to normally record continuously at a lower frame rate, but jump to a higher frame rate for a set period of time when an event is triggered.

1. Setup Menu \> Recording

> **Recording (REC)**: Continuous
> 
> **Continuous Recording Frame Rate** :
> 
> - In this case a low frame rate is recommended
> 
> **Start Recording** : (Select the event(s) to trigger event based recording)  
> **Retrigger recording** : (Use the same event(s) to retrigger recording)  
> **Event Frame Rate** : (Select the frame rate desired for the event based recording)  
> **Recording Time** : (The time required for the Event Based recording to run)  
> **Full Image Recording** : On
> 
> - Set the Full Image Recording parameters for the Continuous Recording

 ![ContinuiousEvent_Resolution1](https://canada1.discourse-cdn.com/flex030/uploads/mobotix/original/2X/5/5ae6630fa4834f29d8316090a746da5ff3112c10.png)

**Switching Resolution when the Event is Triggered**

Now we will need to send an IP Notify via an Action Group to change image size when the Event Based Recording starts

1. Admin Menu \> IP Notify

> **IP Notify Profile Name** : Event\_REC\_Resolution  
> **Predefined Configuration** : Custom Configuration  
> **Destination Address** : (Camera-IP):(Port)  
> **Send Order** : Parallel send to all  
> **Transfer Protocol** : HTTP/1.0 Request  
> **CGI-Path** : /control/control  
> **HTTP Authentication** : (username):(password)  
> **Notification Data** : Plain text  
> **Message** : set&section=recording&size=(required resolution e.g. 1280x960)\>

 ![ContinuiousEvent_Resolution2](https://canada1.discourse-cdn.com/flex030/uploads/mobotix/original/2X/f/f481abef93b82d59106eaac384abb62187814981.png)

1. Setup Menu \> Action Group Overview

Event Selection: \<The event(s) used to trigger event based recording in Setup Menu \> Recording \> Start Recording\>

Action: IP Notify Event\_REC\_Resolution

 ![ContinuiousEvent_Resolution3](https://canada1.discourse-cdn.com/flex030/uploads/mobotix/original/2X/3/3883e7f1e5913e09a2035837b2ba3f2ed8198eab.png)

**Returning the Resolution to the original value after the Event Recording time has expired**

To turn the resolution back to the Continuous Recording Values we need to be a little creative, as changing the resolution resets the Eventd in the camera.

1. Setup Menu \> Event Overview \> Internal Events \> Action Group Termination

> **Action Group:** Select the Action Group created in Step 2 above  
> **Execution Result** : Succeed

 ![ContinuiousEvent_Resolution4](https://canada1.discourse-cdn.com/flex030/uploads/mobotix/original/2X/f/fd5f4ea1b706d2c5fa2b575e7085787d771a9186.png)

1. Setup Menu \> Event Overview \> Meta Event \> Event Logic

> **Set A** : (Internal Event \> Action Group Termination created above)  
> **Set B** : (An event that will never occur, such as recording terminated or a non-existing input or output)  
> **Order of Occurrence** : A \> !B  
> **Maximum Delay** : (This will match the Event Recording time, e.g. event recording time is 10 secs, the maximum delay will be 10 secs)

 ![ContinuiousEvent_Resolution5](https://canada1.discourse-cdn.com/flex030/uploads/mobotix/original/2X/2/215547d0c74a9b59796ab92ce3ef0fa604364892.png)

1. Admin Menu \> IP Notify

> **IP Notify Profile Name** : Continuous\_REC\_Resolution  
> **Predefined Configuration** : Custom Configuration  
> **Destination Address** : (Camera-IP):(Port)  
> **Send Order** : Parallel send to all  
> **Transfer Protocol** : HTTP/1.0 Request  
> **CGI-Path** : /control/control  
> **HTTP Authentication** : (username):(password)  
> **Notification Data** : Plain text  
> **Message** : set&section=recording&size=(required resolution e.g. 1280x960)\>

 ![ContinuiousEvent_Resolution6](https://canada1.discourse-cdn.com/flex030/uploads/mobotix/original/2X/b/b5435dbd14c6136b3340bab39d9027028eca9515.png)

1. Setup Menu \> Action Group Overview

> **Event Selection** : (Meta Event created in Step 2. Above)
> 
> **Action** : IP Notify Continuous\_REC\_Resolution

 ![ContinuiousEvent_Resolution7](https://canada1.discourse-cdn.com/flex030/uploads/mobotix/original/2X/0/0209d5a79d76cccaf1858777ee249e4fdd8a9a4c.png)
